[ Каскадный ] · Стандартный · Линейный PAL N64 games on a NTSC console...?

Here's the instructions, unfortunately I can't retrieve the picture showing which legs of the PIFs go where, has anyone out there saved this?


You need the following parts:
NINTENDO64 ;-) pal and ntsc version
good soldering skills
5 2-way switches
screwdrivers for nintendo systems(since you aint got them,ill explain you how to make them yourself ;-)
some desolder pump or what its called.is not neccessary,but VERY useful,i recommend you get one for about $5 in ur electronics store

the mod works like this:

basically you just cut out the security-chip [PIF(P)-NUS] out of a pal-n64 and connect most pins to the equivalent pins of the ntsc security-chip [PIF-NUS] of a ntsc-n64.the pins
that were not connected are seperated and soldered via 5 two-way switches to the pcb.
now you can switch between pal and ntsc n64 settings and there are NO limitations,EVERY single cart will work
be warned:
you should only do this mod if you are experienced with soldering and stuff!!
while doing this mod,you mess around with the pins of smd-chips,that will break if you bend
them more than 2 times.(if they do,you even need to open the chip itself and this is REALLY tricky,trust me > )

ok,you should do it like this:
open both n64 (how to build a nintendo screwdriver is explained in the cheap mod guide).
now you have 2 choices:
take out the PIF-NUS of a pal n64(use a needle and a soldering iron to lift up the pins) and solder it directly onto the ntsc-pif,but i cant recommend this one,cause its very likely that you break a pin.
for me,the best choice was to desolder both,the ntsc and the pal PIF-NUS,solder both on seperate pcb ( you can buy readymade boards for all kinds of smd-chips in your fav electronic store) and run wires from these pcbs.that means you arent in danger of breaking any pins on the PIFs,cause these little babys are worth a whole n64,you know

once this is done,run wires from a pifs pins that are marked green on the pic to their equivalent pins on the other pif and the pcb(bad explanation,sorry
for example you run a wire from PIF(P)-NUS pin 1 to pin 1 of PIF-NUS and to pin 1 on the pcb,so all pin 1s are hooked up together.
run wires from the pins marked white to ground somewhere on the n64 board.
the other pins running from pif-nus and pif(P)-nus are connected to the pcb via a relais and a 2 way switch(or a jk flip flop + button if ur cool dude
to switch all lines at once (theres no relais in the diagram coz i was too lazy,but u know how to wire them lines up
so you can decide if the n64 uses the pins of the pal or the ntsc pif.
the pink pins on the pcbs are not connected.

thats it, you are done now.
mail me for further questions

воть: http://img.photobucket.com/albums/v204/ret...rityChipMod.jpg

инфа взята отсюда: http://nfggames.com/forum2/index.php?topic=1180.0

фото того, что должно получиться!: http://www.assemblergames.com/forums/showp...53&postcount=61

Это реально сделать, но вот тут задумался зачем?

на счет портативки - блока питания чегото не видно, а я уверяю что батарейками там не отмашешься - жрет то она дай бог каждому
под 2 ампера ток идет

Это реально сделать, но вот тут задумался зачем?

на счет портативки - блока питания чегото не видно, а я уверяю что батарейками там не отмашешься - жрет то она дай бог каждому
под 2 ампера ток идет

Наверное можно придумать слот для расширенной батареи ПСП Слим и т.п. Вообще штука забористая, я бы тыщ за 12 взял бы.